3PCS transformers green wiring connection terminal 130/150W HV CO2 PSU for 1850 CO2 tube 150W CO2 laser tube driver

rubylasertech

ZS-130WX CO2 laser power supply

Feature：

1. Control is simple: This 130W CO2 power supplies use high or low level control, the use of TTL-level control of the laser can start and stop. At the same time it increases the protection switch, testing is through the external water and ventilation on this high voltage CO2 power supplies.

2.This laser tube's CO2 power supplies have a built-in network cable interface, which can be used to connect with external LCD module through the network cable. The external LCD module can display the working status, output current and common fault codes. This is helpful for operators to understand the working status of 130W CO2 power supplies and quickly solve problems. The output current can be adjusted through the rotary potentiometer of the liquid crystal module.

3. Good compatibility: The high voltage CO2 power supplies can drive EFR,Yongli,SPT,Weiju and other brand 1.6 or 1.65 meter length 130W CO2 laser tube and it also have a strong adaptability and fast response, cutting advantages of good effect.

4. This laser tube's CO2 power supplies adopt G/P/L/G/IN/5V as control signal output interface.The high voltage CO2 power supplies adopts aluminum upper cover and base, and galvanized steel shell.

5. Protection function: This laser tube's CO2 power supplies have open circuit protection: Under the condition of good protective earth, the high voltage CO2 power supplies can work in open-circuit for a short time, which could avoid the damage to the 130W CO2 power supplies

6. The laser tube's CO2 power supplies has stable working performance: Each high voltage CO2 power supplies has been much more rigorous testing procedures, under full load high temperature (52~55 degrees Celsius) 24 hours of aging, to ensure the stability of each 130W CO2 power supplies.

7.Laser power control is simple on this laser tube's CO2 power supplies, 0-5V analog signal control the laser power can be used, It can also use the PWM (pulse width modulation) signal to control output laser power.


8. It uses the latest silicon carbide to replaces traditional transistors. The silicom carbide has high efficiency, low heat generation and low failure rate characteristics.Which make this 130W laser power supplies more suitable for long-time uninterrupted works in hot environment.
9.The silicon carbide reduces circuit's quantity, which reduces failure rate and keep consistency in output parameters. Enable laser cutting power supply have better engraving and cutting effects
10. It adopts patch assembly process, which is fully automated and standardized It uses HD cameras to detect circuit boards, assembled components and soldering effects. The two methods reduces the possibility of human error causing unqualified CO2 laser power source
11. It adopts silicone tube to wrap output HV cable to prevent electric sparks from splashing and protect operators and equipment, which allowing CO2 laser tube's power supply work normally in humid environments
12. 90-270V Voltage stabilizer is optional.

13. This 130W CO2 laser power supply can support LCD display screen which can show power supply's working status,failture code and output current. Also output current can be adjusted at the screen. Single channel LCD display screen is default. 4/8 channels LCD display screen is optional.




00 wire connection.jpg

Specification：

Input

Input voltage

AC220V±10% (AC110V specified while order)

AC frequency

47~440HZ

Maximum input power

970W

Maximum input current

4.3A

Output

Maximum output voltage

40KV

Maximum output current

36mA

(depending on the laser tubes of different manufacturers)

Efficiency

More than 90% (Full load)

Response speed

Not more than 1ms

Control lnterace

TTL multilevel switching control,effective level can be high and low selection (see control wining diagram)

Insulation

lnput-output

AC 1500V 1 minutes not more than 10mA

lnput-shell

AC 1500V 1 minutes not more than10mA

Output-shell

Connection

Open Circuit Protection

Can be short circuit (requires a good grounding shell,while avoiding the positive electrode and the shell between the arc)

Environmental Requested

Working temperature

-10℃~50℃

Storage of temperature

-20℃~75℃

Relative Humidity

Maximum 85%RH (non-condensing)

Altitude

100,000 feet of work

200,000 feet of storage,dose not work

Cooling methods

Forced air cooling (fan cooling)

Dimensions (LxWxH)

305mmx142mmx95mm